---
title: "Fence Post Spacing: How Far Apart Posts Go for Each Fence Type"
description: "Wood posts go about 6 to 8 feet apart, vinyl and aluminum follow the panel, chain link runs 8 to 10 feet. See each maker's figure and what changes the layout."
url: "https://portillo-fences.com/blog/fence-post-spacing/"
lang: "en"
published: "2026-11-21"
modified: "2026-11-21"
tags: ["fence posts","fence installation","fence cost"]
image: "https://portillo-fences.com/images/blog/fence-post-spacing/featured.jpg"
---

![Fence Post Spacing: How Far Apart Posts Go for Each Fence Type](https://portillo-fences.com/images/blog/fence-post-spacing/featured.jpg)

Fence & Gate Blog

# Fence Post Spacing: How Far Apart Posts Go for Each Fence Type

Wood posts go about 6 to 8 feet apart, vinyl and aluminum follow the panel, chain link runs 8 to 10 feet. See each maker's figure and what changes the layout.

[Get a Free Estimate](https://portillo-fences.com/contact-us/) [(845) 282-3336](tel:+18452823336)

November 21, 2026

- fence posts
- fence installation
- fence cost

[Wood fence](https://portillo-fences.com/wood-fencing/) posts usually go 6 to 8 feet apart on center, vinyl and aluminum posts follow the width of the panel, and chain link posts run 8 to 10 feet apart. The exact number depends on the product you pick, so the layout on your property starts with the maker's installation sheet, not a single rule of thumb.

Spacing matters because every post means a hole, a footing, a cap and a connection to the panel. Closer posts cost more up front and make a stiffer fence. Wider posts save money until the first hard wind or the first gate that sags.

Each fence type has its own published figure, and wind, [gates](https://portillo-fences.com/gates/), corners and slopes push the number tighter on Hudson Valley lots. Post count then flows straight into your quote.

## Key Takeaways

Wood

Wood fences typically run 6 to 8 feet on center, and one maker sets posts at the rail length plus 2 inches.

Vinyl and aluminum

Panel width sets the spacing, so a post cannot be moved freely the way it can on a wood fence.

Chain link

Posts run 8 to 10 feet apart, and a taller or windier fence should be closer, at 6 to 8 feet.

Gates and corners

Gate openings and corners get their own posts and are laid out before the ordinary line posts.

Cost

A 100-foot run needs about 11 posts at 10-foot spacing and about 18 at 6-foot spacing.

## Post Spacing by Fence Type

Lowe's gives a typical spacing of [6 to 8 feet on center for wood fences](https://www.lowes.com/n/how-to/install-a-wood-fence). Master Halco's [PostMaster Plus solid wood guide](https://www.masterhalco.com/hubfs/MH%20PDF%20Files/PostMaster-Plus-Downloads/PostMaster-Plus-Installation/PM-Plus-Install-Vertical.pdf?hsLang=en) is more exact. It sets line posts at the rail length plus 2 inches on center, so an 8-foot rail gives 98-inch spacing before any site adjustment. Master Halco says the figure can change with board selection, fence height and ground slope.

![A man kneeling on a lawn drives a stake with a mallet and stretches a tape measure to the next stake, with a wood fence panel leaning on a tree](https://portillo-fences.com/images/blog/fence-post-spacing/stake-layout.jpg)

Marking every post location with a stake before digging shows how many holes the run really needs.

The figures for the other systems come from their makers' installation guides, and they differ more than most people expect. The table puts them side by side.

## Published post spacing by fence type, on center

Spacing on center: \---

Whose figure: \---

Tap a row to open it.

The chain link figures come from [Chain Link Fittings' post-spacing FAQ](https://chainlinkfittings.com/store/resources/resources-hub/frequently-asked-questions-about-chain-link-fence.html), which treats 8 to 10 feet as typical practice. Its spacing chart assumes 10-foot centers where the run divides evenly, so a run that does not divide evenly needs its posts adjusted.

Read the split rail row with care. [Tangent's split-rail system](https://tangentmaterials.com/wp-content/uploads/2021/03/S-0012-5721Tangent-Split-Rail-Fence-Install-Guide-Web.pdf) is molded HDPE, not wood, so it is one maker's figure and not a rule for every split rail fence. Traditional wood split rail follows the rail length and the instructions of the rail you buy. Confirm the rail length before any post goes in the ground.

## Why Vinyl and Aluminum Spacing Is Fixed

Vinyl and aluminum arrive as assembled sections. The rails, brackets, pickets and panel ends are built to fit the posts at set distances. [CertainTeed's vinyl instructions](https://www.yumpu.com/en/document/view/26307614/vinyl-fence-installation-instructions-certainteed) list a separate center-to-center measurement for each style. [Phoenix Vinyl's manual](https://phoenixfence.ca/documents/vinyl/overview-and-warranty/pro-vinyl-fence-post-mount-installation-manual.pdf) gives 74 inches for 6-foot sections and 96 inches for 8-foot sections.

Lowe's [pre-built vinyl guide](https://pdf.lowes.com/productdocuments/c9b21336-10c3-4060-b3f1-55dda96d9307/02858283.pdf) states the layout as panel width plus post width, with allowance for the brackets. That is why a vinyl post cannot slide a few inches the way a wood post can when the rails are cut in the field.

Aluminum works the same way. [Gemstone](https://www.aluminum-fence.com/wp-content/uploads/2024/02/Gemstone_Aluminum_Fence_Install.pdf) and [ForgeRight](https://images.thdstatic.com/catalog/pdfImages/4d/4d57f9cf-7ea1-45e1-ae16-14c4104abe89.pdf) both call for 72 1/2 inches on center. ForgeRight lets you cut a panel, as long as you leave the specified rail clearance at the cut end.

![Two men fitting a white vinyl privacy panel between two posts set in fresh concrete, one holding the panel and one checking a post with a level](https://portillo-fences.com/images/blog/fence-post-spacing/vinyl-panel-fit.jpg)

A vinyl panel only fits between posts set to the maker's measurement, so the crew checks the gap before the concrete sets.

When a run does not divide evenly into the panel width, a vinyl or [aluminum fence](https://portillo-fences.com/aluminum-fencing/) may need an extra post or a cut section that follows that product line's instructions. Our [vinyl fencing](https://portillo-fences.com/vinyl-fencing/) page covers what that looks like on a real property.

## What Pushes Posts Closer Together

Closer spacing goes where the fence carries more wind or side load. Master Halco says spacing varies with local conditions and wind exposure. Chain Link Fittings holds chain link to 10 feet at most, and drops to 6 to 8 feet for taller fences or windy locations. On 100 feet, that is the difference between about 11 posts and as many as 18. A solid privacy fence on an open hilltop catches far more wind than a picket fence behind the house.

Gates, corners and slopes each change the layout in their own way.

- **Gates:** Master Halco separates line, corner and gate posts and recommends shorter fence sections near gates or buildings. ForgeRight says to set gate posts 1 inch wider than the gate itself for hinge clearance. Lay out the gate opening first, then fill in line posts.
- **Corners:** Corners take corner or terminal posts, and Master Halco suggests shorter sections there so the layout fits. On chain link, corners and gate openings use terminal posts because the mesh tension concentrates load there.
- **Slopes:** Master Halco says sloped runs may need modified spacing and diagonal cuts at the rail ends so rails sit flush against the posts. [American Vinyl Works](https://americanvinylworks.com/pages/how-to-guide) says vinyl pickets need clearance inside the rail pockets on a slope and may need a slight angled cut. ForgeRight says its aluminum panels can follow an incline by pushing the panel up or down.
- **Racking or stepping:** The [Aluminum Fence FAQ](https://www.aluminum-fence.net/faq) explains that some aluminum systems are rackable, while others need stepped sections or specially fabricated ones. Racked panels follow the ground in one angled line, and stepped panels stay level and drop at each post. The maker's slope limit decides which one you can use.
- **Uneven ground:** [Tangent's guide](https://tangentmaterials.com/wp-content/uploads/2021/03/S-0012-5721Tangent-Split-Rail-Fence-Install-Guide-Web.pdf) calls for less than 8-foot spacing where terrain is not level or where the fence takes side loads. It also allows the rail slots to be opened so the rails can follow a nonlevel fence line.

Hudson Valley lots tend to be rocky and sloped, so expect some of these adjustments. Post depth is a separate question, and our page on [frost depth for fence posts](https://portillo-fences.com/blog/frost-depth-fence-posts-hudson-valley/) covers it by municipality. For what the post itself is made of, see [steel versus wood fence posts](https://portillo-fences.com/blog/steel-vs-wood-fence-posts/).

![A white vinyl privacy fence stepping down a grassy slope in sections past a maple tree and a low stone wall, with a gate beside a driveway](https://portillo-fences.com/images/blog/fence-post-spacing/sloped-fence-line.jpg)

On a slope the panels either rack to follow the ground or step down in sections, depending on the product.

## What Post Count Does to Your Quote

Closer spacing adds posts, concrete, digging, plumbing and alignment time. The effect is biggest on solid privacy fences, gates, corners, windy sites, rocky soil and slopes. On a straight 100-foot run with no gates, the approximate counts look like this:

- 10-foot spacing: about 11 posts.
- 8-foot spacing: about 14 posts.
- 6-foot spacing: about 18 posts.

Corners, gates and end posts change those numbers, and so does adjusting the run into equal sections. A wood fence can often finish with a shorter last section. Vinyl and aluminum may need an added post when the run does not divide into the standard panel width.

Published prices show why post count is only part of the picture. [ProMatcher's Westchester County page](https://fences.promatcher.com/cost/westchester-county-ny-fences-costs-prices.aspx) lists a 4-foot wood fence at $22.26 to $27.03 per linear foot for [Yonkers](https://portillo-fences.com/yonkers-ny/), reported May 20, 2021. It lists a 4-foot [chain link fence](https://portillo-fences.com/chain-link-fencing/) at $17.49 to $23.85 per linear foot for [Port Chester](https://portillo-fences.com/port-chester-ny/), reported October 21, 2019. Both are older figures, so treat them as a rough Westchester reference. Our guide to [what a fence costs in the Hudson Valley](https://portillo-fences.com/blog/fence-cost-hudson-valley/) puts current planning ranges for each material in one place.

A lower post count can cut materials and digging, but only while the spacing stays within the maker's or installer's structural guidance. When you compare two quotes, compare the number of posts and footings, the material, the gates and the site work, not only the price per foot.

![A man in safety glasses checking a wood post with a level in a dug hole while a woman crouches at a row of posts along an orange string line](https://portillo-fences.com/images/blog/fence-post-spacing/setting-line-post.jpg)

Each added post means another hole, another footing and another check against the string line.

## Frequently Asked Questions

**How far apart should wood fence posts be?**

Lowe's gives 6 to 8 feet on center as the typical range. Master Halco's PostMaster Plus system sets line posts at the rail length plus 2 inches, which is 98 inches for an 8-foot rail. Taller fences, wind exposure and slopes can call for closer posts.

**Can I space [vinyl fence](https://portillo-fences.com/vinyl-fencing/) posts wider to save money?**

No. Vinyl sections are built to fit posts at a set measurement. CertainTeed lists 72 or 73 inches for its 6-foot Newport sections, and Phoenix lists 74 inches. Spacing the posts wider than the section means the panel will not seat in the brackets.

**How far apart are aluminum fence posts?**

Gemstone and ForgeRight both specify 72 1/2 inches on center for their residential panels. Gate posts are laid out separately. ForgeRight says to set them 1 inch wider than the gate.

**What is the maximum spacing for chain link?**

Chain Link Fittings says 8 to 10 feet is typical and the spacing should not exceed 10 feet. For taller fences or windy locations it recommends 6 to 8 feet. Corners and gate openings use terminal posts.

**Does a gate change where the other posts go?**

Yes. A gate needs dedicated gate posts rather than ordinary line posts, and the opening is laid out before the line posts. Master Halco also recommends shorter fence sections near gates.

**Does spacing change on a slope?**

It can. Master Halco says sloped runs may need modified spacing and angled rail cuts. Some aluminum panels rack to follow the hill, and others step down, so the maker's slope limit decides which one you can use.

**Quiz: Check yourself**

1. What does Master Halco's PostMaster Plus guide give for line post spacing on wood?
   - The rail length plus 2 inches on center **(correct answer)**
   - Always exactly 6 feet
   - The rail length minus 2 inches
2. How far apart are aluminum posts for Gemstone and ForgeRight residential panels?
   - 72 1/2 inches on center **(correct answer)**
   - 10 feet on center
   - 48 inches on center
3. What is the most Chain Link Fittings allows between chain link posts?
   - 10 feet **(correct answer)**
   - 12 feet
   - 15 feet
4. About how many posts does a straight 100-foot run need at 6-foot spacing?
   - About 18 **(correct answer)**
   - About 11
   - About 6

Start with the maker's installation sheet for the fence you choose, then adjust for wind, gates, corners and slope. Ask for a quote that lists the post count, the footings, the gate posts and any rock or slope work as separate lines, so you can see what the spacing is costing you.

[Portillo Fences and Gates](https://portillo-fences.com/) lays out and installs [wood fencing](https://portillo-fences.com/wood-fencing/) and other [residential fencing](https://portillo-fences.com/residential-fencing/) for homeowners in Putnam, Westchester, Dutchess, Orange, Ulster and Rockland counties. To plan your layout and get a quote, use our [contact page](https://portillo-fences.com/contact-us/) or call [(845) 282-3336](tel:+18452823336).

## Ready to talk through your project?

Get a free estimate from a licensed, insured Hudson Valley fence and gate team.

[Get a Free Estimate](https://portillo-fences.com/contact-us/)[Call (845) 282-3336](tel:+18452823336)
